|
 
|
SERVICE > TECHNICAL TERMS
>>
|
PRODUCT TYPE ABBREVIATIONS
Li
|
: |
strand conductor construction |
| F |
: |
finest-strand construction |
| Y |
: |
plastic based on PVC |
| 2Y |
: |
plastic based on PE |
| 9Y |
: |
plastic based on PP |
| YW |
: |
national abbreviation for temperature-resistant
plastic based on PVC |
| 11Y |
: |
Kunststoff auf PUR-Basis |
| 12Y |
: |
plastic based on TPE-E |
| 30Y |
: |
thermoplasic natural rubber |
| 31Y |
: |
temperature-resistant thermoplasic elastomer |
| 32Y |
: |
special temperature-resistant thermoplasic elastomer |
| X |
: |
radial distributed PVC |
| 2X |
: |
cross-linked polyehylene |
| 11X |
: |
radial distributed PUR |
| SK |
: |
suitable for dragchains |
| FRNC |
: |
flame retardant and halogen-free wire |
| -J |
: |
including green-yellow ground wire |
| -O |
: |
without green-yellow ground wire |
| -B |
: |
coloured wires |
| -Z |
: |
number print |
| -C |
: |
screening meshwork |
general harmonised abbreviations:
H
|
: |
harmonised wires |
| S |
: |
special wires |
| 03 |
: |
nominal voltage Uo/U 300/300 V |
| 05 |
: |
nominal voltage Uo/U 300/500 V |
| 07 |
|
nominal voltage Uo/U 450/470 V |
| V |
: |
PVC based wire insulation |
| V |
: |
PVC based sheath material |
| V2 |
: |
harmonised abbreviation for temperature-resistant PVC (+ 90° C) |
| -F |
: |
finely-wired construction of bunched conductors according to DIN VDE 0281 |
| 3G |
: |
twisted wire with three wires and green-yellow ground wire |
| 0,75 |
: |
0,75 mm² conductor cross section |
|
>>
|
TYPE ABBREVIATION OF AUTOMOTIVE WIRES
| wire type |
FL
|
: |
automotive wire, low voltage |
| FZL |
: |
automotive wire, high voltage, (ignition line) |
| application of used insulation and sheath material |
Y
|
: |
PVC, polyvinyl chloride |
| type of used shielding material |
B
|
: |
foil shield with ground wire |
| D |
: |
copper-based single wire shield |
| C |
|
copper screen |
| non-extruded sheaths |
G
|
: |
fibre glass mesh |
| T |
: |
textile weave |
| special construction features |
R
|
: |
4 reduced insulation thickness according to DIN ISO 6722,
Part 4 |
| U |
: |
ultra reduced insulation thickness |
| S |
: |
insulation thickness bigger than according to
DIN ISO 6722, Part 3 |
| F |
: |
non-seperable flat wire |
| Z |
: |
multiple core, non-separable wire |
| M |
: |
other conductor materials than E-Cu or resistance alloies |
| W |
: |
resistance conductor |
| number of wires and conductor cross section |
0,5
|
: |
conductor cross section 0,5 mm² |
| 0,5 sn |
: |
conductor cross section 0,5 mm², tinned |
| 3 x 0,5 |
: |
three wires with conductor cross section 0,5 mm² each |
| W/km |
: |
on resistance conductors information in Ohm/km |
| examples: |
| FLRY 2,50 mm² verz |
: |
FL = automotive wire
R = with reduced insulation thickness
Y = PVC insulation
2,50 mm² verz = conductor cross section 2,50 mm² tinned
|
| FL11Y 16,00 mm² blk |
: |
FL = automotive wire
11Y = PUR sheath
16,00 mm² blk = conductor cross section 16,00 mm² bare
|
| FLRYY 3 x 0,25 mm² blk |
: |
FL = automotive wire
R = with reduced insulation thickness
Y = wire insulation PVC based
Y = sheath insulation PVC based
3 x 0,25 mm² blk = three single wires with cross conductor section
0,25 mm² each, bare |
|
|
